Pressure Regulator Service in Nevada | 911 Plumbing NV
from $299
Plumbing Pressure Regulator Service in Nevada
Service and replacement of pressure-reducing valves (PRVs) — Watts, Zurn, and Cash Acme. We test your incoming pressure, rebuild or replace a failed regulator, and set the house to a safe 50-to-70 PSI to protect the whole system.
Pressure Regulator Service is one part of our plumbing maintenance coverage in Nevada. For the full picture — symptoms, costs, and when to repair vs. replace — start with the complete Plumbing Maintenance guide, or browse every plumbing maintenance service we offer.
The pressure-reducing valve is a small brass device where the water line enters the house, and it does one critical job: step high, variable municipal pressure down to a safe, steady level the home's plumbing can handle. When it fails — and every PRV eventually does, usually in 7 to 12 years — it either lets pressure climb dangerously high or chokes it too low, and a home with no PRV at all takes whatever the city sends, which can spike past 100 PSI. PRV service tests your incoming pressure and rebuilds or replaces the regulator so the whole {city} system runs in a safe range.
High pressure is deceptively destructive because it does its damage slowly and everywhere at once — it hammers the pipes, shortens the life of the water heater and every appliance with a fill valve, wears out faucet cartridges and toilet fill valves, and stresses each fitting toward the burst that finally announces the problem. We put a gauge on the system to read the actual static and how it behaves, then set the replacement PRV to the ideal 50-to-70 PSI. Where a home has no regulator at all, adding one is one of the highest-value protections across a {county} system.
PRVs are serviceable but not forever. A regulator fouled by sediment can sometimes be rebuilt with a new cartridge or bonnet assembly, but a corroded or failed body is replaced outright — we install Watts, Zurn, and Cash Acme, size the valve to the service line, and set it under live pressure. We also confirm the home has a properly sized thermal expansion tank, because a PRV acts as a check valve that closes the system and turns water-heater expansion into a pressure spike with nowhere to go. Correcting both together protects the whole {areas} home.
Signs you need pressure regulator service
Pressure reads over 80 PSI
A gauge reading above 80 PSI means the regulator has failed high or the home has none. Bringing it back into range protects every pipe, fixture, and appliance in the the United States home.
Water hammer and toilets that run or leak are classic symptoms of over-pressure stressing the fixtures. Setting the PRV correctly quiets the system across the United States.
Appliances failing early
Water heaters, dishwashers, and washing machines that wear out fast are often being battered by high pressure. A working regulator extends their life in the your area home.
Pressure creeping up or dropping
Pressure that drifts high over months or sags low means the PRV is losing its ability to hold a setpoint. Rebuilding or replacing it steadies the the United States system.
No regulator on the main
A home with no PRV takes raw municipal pressure, which can spike well past safe levels. Adding one is a high-value upgrade for the the United States plumbing.
Common causes & what we fix
PRV wear and age
The regulator's internal diaphragm and seat wear out over 7 to 12 years until it can't hold pressure. Age alone is the most common reason a the United States PRV needs service.
Sediment fouling
Grit and mineral debris lodge in the valve seat and diaphragm, driving the pressure erratic. A rebuild kit or a new valve clears the fouling in the the United States home.
Diaphragm failure
The rubber diaphragm that regulates flow cracks and fails, causing the PRV to lose control of the pressure. Replacing the cartridge or the valve restores regulation across your area.
Missing regulator
Some older homes and high-pressure areas never had a PRV installed, exposing the plumbing to raw municipal pressure. Adding one protects the whole the United States system.
Municipal high pressure
Cities deliver high pressure to reach upper floors and hydrants, often well above what a home should see. The PRV is the only thing standing between that and the the United States fixtures.
Our process
1
Call or schedule online. Book your pressure regulator service in Nevada online or by phone and pick a 2-hour window. We confirm in under five minutes with the assigned tech's name and photo.
2
On-site diagnosis. On arrival we diagnose the pressure regulator service on-site — free for most repairs, $39 on minor service calls (waived if you proceed). You see the issue and the fix before we start.
3
Flat-rate quote. You get a flat-rate pressure regulator service quote in writing, good for 30 days — no hourly creep and no add-ons after the fact.
4
Same-visit fix. Most pressure regulator service work finishes the same visit: our trucks carry the common valves, fittings, water heater parts, and fixtures, so a second trip is rare.
How much does pressure regulator service cost in Nevada?
Pressure Regulator Service the United States starts at from $299, every pressure regulator service quote is flat-rate and presented in writing before work begins — no surprise add-ons, no hourly creep. Seniors (65+) and military save 10% on labor, and financing covers projects over $1,500 at 0% APR for 12 months, with no prepayment penalty.
Why homeowners in Nevada choose us for pressure regulator service
We've been a trusted choice since 1974 — over 50 years of family-owned plumbing service across Nevada. Our techs are CSLB-licensed (#1098234), background-checked, and complete an internal 12-week training program before rolling on calls alone.
Our pressure regulator service carries a 10-year workmanship guarantee — separate from any manufacturer warranty on the parts themselves. If the pressure regulator service we performed fails because of how we did it, we come back and fix it free for a full decade. Water heaters and fixtures we install are backed by their full manufacturer warranty, and the parts and accessories we fit carry standard 1–5 year warranties by item.
We quote pressure regulator service on honest scope: no unnecessary up-sell, salaried (never commissioned) technicians, and a transparent diagnostic so you see exactly what we see — including the parts still in good shape. If a repair is the right call we say so; if replacement is the better long-term economics, we say that. The flat-rate pressure regulator service quote is written and good for 30 days.
Areas we serve for pressure regulator service
We provide pressure regulator service throughout Nevada, with fast coverage in every major Nevada metro.
Reach times for pressure regulator service vary by traffic and time of day, so we quote an accurate ETA when you call — and the dispatch line routes straight to an on-call technician, no voicemail in between.
Frequently asked about pressure regulator service
Top questions homeowners searching for Pressure Regulator Service near me ask us:
How do I know if my pressure regulator has failed?
The signs are pressure over 80 PSI on a gauge, banging pipes, running toilets, and appliances wearing out early. We test your actual static pressure at the the United States home to confirm whether the PRV has failed high, low, or is missing entirely.
Can a PRV be repaired or does it need replacing?
Sometimes it can be rebuilt with a new cartridge or bonnet if the body is sound and only fouled by sediment. A corroded or failed body is replaced outright — we install Watts, Zurn, and Cash Acme and set it to safe range in your the United States home.
What pressure should the regulator be set to?
The ideal range is 50 to 70 PSI — strong enough for good flow, low enough to protect the system. We set the replacement PRV under live pressure and verify it holds across the your area home.
Do I need an expansion tank with a PRV?
Usually yes — a PRV acts as a check valve that closes the system, so water-heater expansion has nowhere to go and spikes the pressure. Code requires a properly sized expansion tank on a closed system, and we confirm or add one in the the United States home.
How long does PRV replacement take?
Most PRV replacements run 1–2 hours — we shut off, cut in the new valve, set the pressure, and verify it holds. We size the regulator to your service line and serve ZIPs across the United States.